2006 BMW 3 Series

Canadian MSRP
$35,100 - $84,400
2006 BMW 3 Series

Key Specifications for 2006 BMW 3 Series

Fuel Economy 6.7 - 14.9 City/HWY combined
Horsepower 174 - 333 hp
Drivetrain Rear-Wheel Drive, All-Wheel Drive
Engine Gasoline
Torque 170 - 262 ft-lb
Seats 4 - 5
 

Review & Compare:
2006 BMW 3 Series Trims

The 2006 BMW 3 Series has 15 trims. Below you will be able to review all the trims with the option to compare.
15 trims available
Select 1 more trim

Photos

No content available

AutoTrader Review

N/A

This vehicle has not yet been reviewed

Reviews and News

View All Articles

Recall Information

Recall number
Recall date
System affected
Model year(s) affected
Recall number
2020-009
Recall date
2020-01-15
System affected
Airbag
Model year(s) affected
2000 2001 2002 2003 2004 2005 2006
Manufacturer Recall Number:
72 80 20RC
Units Affected:
20,070
Notification Type:
Safety Mfr
Issue: This recall is for certain vehicles that had an airbag inflator replaced as a part of an earlier recall campaign. This recall provides a final repair. Long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, may eventually degrade the propellant contained in the passenger-front airbag. This could cause the airbag to deploy with more force than normal. If the airbag inflator ruptures, fragments could be propelled toward vehicle occupants or cause damage to the airbag assembly, preventing its proper function. Safety Risk: If the vehicle is involved in a crash requiring an airbag deployment, the airbag inflator could rupture and create a risk of injury. Corrective Actions: Owners will be notified by mail and instructed to take their vehicle to a dealer to inspect the passenger-front airbag module. The passenger-front airbag module will be replaced as necessary. Note: The Canadian climate results in the propellant degrading slowly. This recall is being conducted as a precaution to address future risk. It is expected that all airbag inflators will be replaced before their function would be affected.
Recall number
2019-170
Recall date
2019-04-05
System affected
Engine
Model year(s) affected
2006
Manufacturer Recall Number:
Units Affected:
15,466
Notification Type:
Safety Mfr
Issue: On certain vehicles equipped with an N52 6-cylinder engine, a manufacturing problem could cause the PCV valve heater to overheat. Safety Risk: An overheated engine PCV valve heater could create the risk of a fire. Corrective Actions: The company will notify owners by mail and instruct you to take your vehicle to a dealer to replace the PCV valve heater.
Recall number
2017-588
Recall date
2017-11-30
System affected
Electrical
Model year(s) affected
2006 2007 2008 2009 2010 2011
Manufacturer Recall Number:
Units Affected:
75,744
Notification Type:
Safety TC
On certain vehicles, the blower regulator wiring harness crimp connection could start to corrode over time. This in combination with high current flow (IE maximum blower fan speed) could cause the harness to overheat and melt, which could lead to a fire causing injury and/or damage to property. Correction: Dealers will replace the blower regulator wiring harness and inspect other components for damage, replacing them as necessary.
Recall number
2016-142
Recall date
2016-03-31
System affected
Airbag
Model year(s) affected
2006 2007 2008 2009 2010 2011 2012 2013
Manufacturer Recall Number:
Units Affected:
104,151
Notification Type:
Recalls Audit
On certain vehicles, the driver frontal airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Correction: Dealers will replace the front driver air bag inflator or air bag module, depending on the vehicle model.
Recall number
2015-230
Recall date
2015-05-27
System affected
Airbag
Model year(s) affected
2002 2003 2004 2005 2006
Manufacturer Recall Number:
Units Affected:
30,668
Notification Type:
Safety Mfr
On certain vehicles, the driver frontal airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Note: This recall supersedes special service campaign 2014-587. Correction: Dealers will replace the airbag module.
Recall number
2014-587
Recall date
2014-12-22
System affected
Airbag
Model year(s) affected
2004 2005 2006
Manufacturer Recall Number:
Units Affected:
11,131
Notification Type:
Superseded
BMW Canada is conducting a voluntary Safety Improvement Campaign concerning the driver's airbag inflator on certain vehicles equipped with Takata airbags. BMW will replace the driver's inflator on affected vehicles. This action is not being conducted under the requirements of the Motor Vehicle Safety Act. Note: This special service campaign was replaced by recall 2015230. Please see recall 2015230 for more information: Click here for more information
Recall number
2014-299
Recall date
2014-07-16
System affected
Airbag
Model year(s) affected
2000 2001 2002 2003 2004 2005 2006
Manufacturer Recall Number:
Units Affected:
40,915
Notification Type:
Safety Mfr
On certain vehicles, the passenger (frontal) airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment during a crash where deployment is warranted, increasing the risk of personal injury to the seat occupant. Correction: Dealers will replace the passenger airbag. Note: This is an expansion of recall 2013148.
Recall number
2013-238
Recall date
2013-07-05
System affected
Airbag
Model year(s) affected
2006 2007
Manufacturer Recall Number:
Units Affected:
15,294
Notification Type:
Safety TC
On certain vehicles, the front passenger seat occupant detection mat can fatigue over time. As a result, the passenger airbag could deactivate, illuminating the airbag warning lamp and the passenger airbag ON/OFF lamp. Failure of the passenger airbag to deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Correction: Vehicles will receive special extended warranty coverage of 10 years from first registration. Under this special coverage program, vehicles which experience this condition will have the occupant detection mat replaced.
Recall number
2008-307
Recall date
2008-08-26
System affected
Seats And Restraints
Model year(s) affected
2006
Manufacturer Recall Number:
Units Affected:
8,090
Notification Type:
Safety Mfr
On certain vehicles, the front passenger seat occupant detection mat can fatigue during field usage depending on the seat configuration, vehicle geometry, manner and frequency of front passenger entry/exit. Over time micro cracks could develop in the side flanks of the mat, which could lead to a break of the conductive path and the system will recognize a failure and with exception of head protection system the front passenger air bag will be deactivated. The airbag On/Off lamp will be illuminated to make the occupants aware of the deactivation. Correction: The occupant detection mat will be granted a warranty extension of 10 years.
Recall number
2006-267
Recall date
2006-10-17
System affected
Suspension
Model year(s) affected
2006
Manufacturer Recall Number:
Units Affected:
2
Notification Type:
Safety Mfr
On certain vehicles, the bolted connection between the front control arm and swivel bearing may not have received adequate tightening torque during vehicle assembly. As a result, this bolted connection could loosen and/or break, affecting vehicle stability and control. Correction: Dealers will verify the bolted connection torque.

Similar Vehicles

Select Another Vehicle
Search now